Chamomile from non-inflated balls

Balloons are strongly associated with childhood and holiday and carry in themselves an amazing aura of magic. It is necessary to inflate it and in the house it immediately becomes more fun and brighter. But the life of the inflated ball, unfortunately, is short. Therefore, flowers from non-inflated balls, Fantasy Flowers, are very popular abroad. The technique of their manufacture is very simple. But it is better to try once than to hear many times. I suggest that you make a daisy from not inflated balls and fill with the magic balls of your house. This summer flower will delight you for a very long time, and in the cold and in the slush give sunny heat. Or maybe you want to share this piece of summer and make such a miracle as a gift to a loved one. Believe me, such a gift will raise you to an unattainable height in the eyes of others. Let's try?
 Chamomile from not inflated balls
Materials and tools. 1. Wire (0.8 mm, for welding) 2. Scotch narrow (width 0.5 - 0.8 cm) 3. Double-sided tape (width 0.8 - 1 cm.) 4. Nippers, pliers 5. Scissors (very sharp) 6. Ruler 7.A small piece of padding polyester or wool. 8. Balls 5 inches pastel (preferably made in Mexico, they are the softest, but durable) - 8 pieces 9. Ball yellow 2 inches (or 5) - 1 piece 10. Balls 9 inch green - 2 pieces 11. Ball for modeling 260 Q - 1 piece
 Materials and tools
Manufacturing steps. 1. We take the wire and cut 9 segments of 30 cm long.
 piece of wire
2. In 8 pieces of wire with pliers bend the ends on both sides and carefully clamp. The bend should be small no more than 3-4 mm.
bend his
 a few delays
 Daisy made of not inflated balls

3. On the 9th billet from one end, with the help of pliers, we twist the spiral, and on the other hand we make a bend similar to the previous frameworks. And put it aside for the time being. This will be the core of our chamomile.
 bend is similar to the previous frameworks
4. We make loops from 8 main pieces of wire.We fold the blank in half, trying not to make a sharp corner on the bend, we connect the ends together, exactly lay out in relation to each other and fasten with several skeins of adhesive tape. The important point: the tape is wound not straight, but at an angle of 45 degrees from top to bottom. This makes the place of twisting more durable and does not allow to slip and unwind.
Bent petals
5. Frames ready. On the turn of the balls. All balls cut pucky at a distance of 1 cm from the edge, and the modeling ball (SMM) only pucku.
Crop balls
6. Carefully squeezing the frame on the sides, put on a white ball. We pull it to the end and throw it onto the fixed loops. Once again tightly tighten a few skeins of Scotch. Similarly do the remaining 7 petals. Put on
 the resulting petal
 squeezing the skeleton on the sides
squeezing the skeleton on the sides
7. On a spiral of a skeleton of a core we wind a synthetic winterizer, forming the center of a flower. The more you want to get it, the more you need to wrap filler.
 we wind the sintepon
8. Stretching the neck of the yellow ball, dress it on the resulting billet. Adhesive tape fix the ball on the stem. If it turned out a little out of alignment, use your fingers to distribute the synthetic winterizer inside the ball to get the result that suits you.
 fix the ball on the stem
 fix the ball on the stem
9. Begin to assemble the flower. Put petals on top of each other, lay them around the core. Trim the height of the petals on the top edge. Check the uniformity of the calculations, and tightly fastening, fix with adhesive tape. Flush tightly with adhesive tape to the end of the petals.
 Starting the flower assembly
 We start the assembly of the flower
10. One by one, carefully open all the petals of the resulting flower.
Starting the flower assembly
 open all the petals
11. We take the modeling ball (SHDM) and cut it along, leaving 1 cm uncut near the tip.
 open all petals
12. We cut off the top of one green ball and cut the sepal.
 cut it along
 we cut off the top
13. Apply 1 turn of double-sided tape on the border of the bend of the petals, and put on the place the sepal. Fix with scotch.
cut off the top
 flower assembly
 flower assembly
14. On the second green ball, we make cuts on the top and sides, then finely cut into strips to form chamomile leaves. With the help of double-sided and ordinary adhesive tape fastened to the transition point frompetals to the stem.
flower assembly
 flower assembly completed
make cuts on top

Getting to the design of the stem. To do this, we need a simulation ball, already prepared by us. String it on the stem and wind it up to the petal. The ball must be tightened and evenly laid so that there is no gap. After reaching the petal, scroll first slightly above it, then, continuing to reel, go back slightly (under the petal), and then move to the very top. This will allow to fix it (crosswise) correctly.
we cut stripes
 from petals to stem
Let's get down to decorating the stem
15. If you have an extra ball left, do not wind it until it runs out. Just cut off the remainder. Using a small piece of double-sided tape, glue the end of the MDA and fix in addition,putting the stalk on the stalk in this place from the ball itself.
 Start the design of the stem
If there is an extra ball left
 If there is an extra ball
 If there is excess sha p
16. Our flower is ready!
 Our flower is ready
Similar flowers live for six months or more. Do not like dust, moisture and direct sunlight. Successful creativity!
 Chamomile from not inflated balls